Recommendations for choosing engine oil for the LADA Largus engine. Car oils and everything you need to know about engine oils What kind of oil in largus

After a run of 15.000 km. the question becomes relevant, what kind of oil should be poured into Lada Largus to ensure the normal operation of the engine. The quality of engine oil directly affects the operation of the engine and the resistance of its parts to premature wear.

If you fill in low-quality oil or which does not meet the manufacturer's recommendations, the life of the car will be reduced. In addition, there is a possibility that if you use a non-recommended brand, they may refuse to service the car under warranty.

(banner_content)
To access the drain plug, the engine protection is dismantled. The plug is unscrewed with an 8 hex wrench and a container for used oil is placed under the drain hole. The draining process takes at least 10 minutes.

Thereafter remove the old filter. If it is not too tight, then it is quite possible to unscrew it by hand. If manually it does not work, then you can use a special device. If not, a regular screwdriver will do. To do this, it is driven into the filter away from the engine and used as a lever to unscrew. The new filter is lubricated with oil and installed on the engine. You don't need to pull hard.

It is enough after contact of the rubber ring of the filter with the engine to tighten it another 2/3 of a turn. Then you need to install the drain plug in place. If the rubber gasket between the plug and the pan is damaged, then it is replaced with a new one. In this case, you can use not a rubber, but a copper gasket.

We are finishing work. Checking

Now you can fill in fresh oil in the amount recommended by the manufacturer. Next, the engine is started and checked control lamp oil pressure. A few seconds after starting, it should certainly go out. After warming up the engine for two minutes, and making sure that everything works, it is turned off. After giving the oil a little time to drain back into the sump, check its level with a dipstick. Top up if necessary.

When using the recommended grade of oils, the frequency of its replacement will be every 15.000 km. If you come across a poor-quality or fake under famous brand, it should be replaced immediately. It is very difficult to identify a fake. Therefore, when deciding what kind of oil to fill in Lada Largus, give preference to trusted sellers and manufacturers. Never buy cheap analogues famous brands oils. It won't lead to anything good.

Greetings to all largus breeders who have looked at this minute on my blog.

Many people change oil immediately after purchase. new car without waiting for the first MOT. Someone is waiting for the car to pass 2,000 km or 10,000 km or even 15,000 km. The service book for Largus indicates that the engine oil is replaced after the first 30,000 km.

Personally, I am one of those drivers who prefer to change the oil in the first days after purchasing a car. I did the same with Largus. I do all subsequent replacements every 10,000 - 15,000 km.

What oil is in the engine from the factory?

Both 8-valve (K7M) and 16-valve (K4M) at AvtoVAZ are filled with modern synthetic oil ELF 5W-30 RN0700. The dealers at the dealership will also recommend this oil to you. Classification according to ACEA A5/B5 - according to API SL/CF.

Judging by many surveys on Largus service sites, many adhere to these recommendations.

But you can use other oils as well. The main thing is that it corresponds to the quality class and viscosity level indicated in the instruction manual. Oil class according to ASEA - A1, A2, A3 and A5; according to API - SL, SM and SN.

Among the leaders are Shell, Lukoil and Zic.

Features of an oil change in Largus

You will need:

1. Square key on 8;

2. New oil filter for Gas engine(7700274177). Be careful, there are fakes;

3. Drain plug washer or sump plug gasket (110265505R). Under this article, it is steel with a rubber insert in the center. It may be entirely copper. Both types cost 30-35 rubles each;

4. Drain container. An old canister of oil or windshield washer fluid is convenient. It's also helpful to find something like a mosquito net or old tulle to put over the canister. So the drain plug does not have to be looked for in mining;

5. Naturally motor oil and straight arms;

From my own experience, I will say that in order to drain the oil from the crankcase, it is not necessary to drive into the pit. On a flat surface, without much difficulty, you can crawl under the front to the drain plug.

The procedure for changing the oil is as follows:

1. On a hot engine, unscrew the drain plug and drain the used oil. It is better not to rush and wait 30 minutes. During this time, the engine will cool down and you will not burn yourself when you unscrew the oil filter;

2. Unscrew the oil filter. You will probably need a puller. I advise you to buy a "Crab" puller, it is everywhere, but the cup puller must be selected according to the size of the filter;

3. You can slightly unscrew the engine filler cap;

4. We twist the drain plug!

5. Install a new filter, after lubricating it with oil. Important: you don’t need to tighten it too much, hand effort is enough! With a strong tightening, the next time the filter will turn away with difficulty;

6. Fill in the required volume of new oil, periodically checking its level with a dipstick;

7. We start the car and let it run for 2 minutes;

8. We turn off the engine and check the oil level. Top up if necessary. If poured, then you need to carefully drain the excess through the drain plug. But just be careful! If you loosen it too much, the plug can pop out and all the oil will naturally pour out. Or pump out through the neck with a syringe and a tube from a dropper.

How much oil to fill in Largus

• K7M (8 valve) - 3.3 liters
• K4M (16 valve) - 4.8 liters

Mark the desired level on the canister, and when you approach it, check the oil level with a dipstick. So it's less likely to spill. The oil is not completely drained from the engine, and some of it remains. Therefore, do not be surprised if you have less oil than recommended. The main thing is that the level on the probe should be between the "min" and "max" marks.

Where to buy oil for Largus?

And now, as promised, I am writing where to buy Elf 5w-30 oil at the lowest price.

In Yaroslavl, the lowest price is offered in the online store logan76.ru. A five-liter canister of oil was bought in it for 1841 rubles. with home delivery. Purchased in March 2016.

All useful and successful purchases!

The choice of engine oil should be given Special attention, since the operation of your vehicle depends on its quality. Therefore, it is necessary not only to replace it on time, but also to know what consumables to fill in. Now you can find out which one is suitable for Lada Largus and how to change it.

[ Hide ]

We do our own oil changes

There is nothing wrong with this process - even a person who has never driven a car can handle it. If you follow the steps and tips described in this article, you can do everything right and your "iron horse" will be very grateful to you.

What oil is suitable?

The choice of engine oil (hereinafter - MM) for replacement at 16 valve engine Lada Largus are the first difficulties faced by a car owner who decides to replace this consumable. At this point, you need to dwell in more detail, since many Lad owners often make mistakes when choosing motor fluid.

As mentioned above, the quality of this consumable affects the operation of the motor, as well as the wear resistance of the elements of the internal combustion engine system. If the filled engine oil is of poor quality or does not meet the recommendations of the vehicle manufacturer, then the service life of the machine is significantly reduced. In addition, if your car is relatively new and is under warranty, then when using a low-quality MM, you may simply be denied engine repair if necessary.

To find out exactly what consumables should be poured into Lada Largus, you should read the service manual for your car. It clearly indicates the necessary parameters and characteristics that a motor fluid should have.

In particular, for a 16-valve Largus engine, the manufacturer recommends using MM that corresponds to the quality classes:

In this case, the consumable must comply with the following viscosity levels according to the SAE standard:

• 5W30;
• 5W40;
• 0W30;
• 0W40.

From the parameters indicated by the manufacturer, you can safely select motor fluids of both foreign and domestic production, namely:

• Shell Helix;
• Lukoil;

Of course, it is imperative that the viscosity grade of the consumable correspond to what the manufacturer recommends. Otherwise, get ready for the problems that will arise in the motor after operating an unsuitable MM.

As for the frequency of replacing the lubricant, if you drive a new car, then the first replacement must be made no earlier than after 15 thousand kilometers. If your car has already survived the first replacement of engine fluid, then it is advisable to reduce the period of its change in the 16-valve engine to 10 thousand kilometers.

Please note if during operation the consumable has lost its properties or characteristics, that is:

• turned black;
• sediments and deposits appeared in it, as well as metal dust and other wear products;
• or if it has become liquid, like water;

then its use in the future will not turn out to be anything good. In this case, it is better to immediately replace the consumable, until not only the internal combustion engine, but the entire lubrication system has suffered from poor-quality fluid.

What to prepare?

So, you are the owner of Lada Largus, who decided to replace the engine fluid. So, you need to prepare everything that may be required in the process of performing work. Prepare:

• a canister with a new MM;
• oil filter;
• set of wrenches;
• tetrahedron on "8";
• an old bucket for collecting old oil;
• old rags.

Step by step instructions

Work on changing the MM should be carried out on a flyover or in a garage with a pit. Also note that it is advisable to replace consumables on a warm engine, otherwise the oil will begin to solidify and will not be able to fully drain from the engine.

1. So, drive your Lada Largus into the pit and crawl under the bottom of the car.
2. Using the appropriate wrenches, dismantle the engine protection. Don't lose the bolts that hold it to the body.
3. While you are at the bottom, take a rag and clean the oil pan as much as possible from dirt and deposits. In particular, the area around the drain plug must be cleaned.
4. Then open the hood of Lada Largus and unscrew the filler cap.
5. Take a square on "8", loosen the drain cap. Place an old bucket prepared to collect waste fluid under the hole and completely unscrew the drain plug. Please note that about five liters of consumable should come out of the system. Also do not forget that the MM itself is hotter if the engine has been warmed up to operating temperature so be careful not to get it on your skin.
6. Also note that under the drain hole you can see a steel washer. It should be inspected: if you notice that the rubber layer around the washer has worn out and it is better to replace the seal, then replace the washer with a new one.
7. Wait about 30 minutes until the lubricant has completely drained from the system.
8. After that, you can screw the drain cap back on. Wipe the oil pan with a clean cloth and remove all consumable smudges from it.
9. Now you need to replace the oil filter element. With its dismantling, many owners of Lada Largus have problems. If you have a special dismantling key, then removing the filter element will not take much time. But if you cannot dismantle it, then take a screwdriver and pierce the filter itself, and then, using the screwdriver as a lever, turn the filter counterclockwise. Please note: it is better to punch the filter in a place closer to the bottom so that you do not accidentally damage the engine fitting.
10. When the filter is removed, its seat on the engine block must be cleaned of deposits and fluid leaks. Apply a few drops of new MM to the sealing gum of the filter element and tighten the component by turning it clockwise until it comes into contact with the sealing gum on the cylinder block. Scroll the MF (oil filter) a little more so that it is firmly installed.
11. Now you need to pour about five liters of engine fluid into the internal combustion engine through filler neck. To be more precise, no more than 4.8 liters of consumable should enter the internal combustion engine. Screw on the filler plug.
12. Turn the key in the ignition switch and check that the dashboard the emergency pressure lamp MM in the engine went out. Also crawl under the bottom and make sure that no consumable is leaking from under the drain plug. In addition, there should also be no smudges from under the filter.
13. Now start the engine and let it run for idling. A few minutes after starting the engine, part of the liquid will drain into the oil pan, so turn off the engine and check the MM level. Add if necessary.

Consider the process of changing the oil in the Lada Largus engine, 8 valves of which work in extreme conditions. According to the regulations, the oil must be changed every 15 thousand km, and at the same time the filter is always replaced. By the way, the filter can be changed “every other time”, although there are no such assumptions in the regulations. The crankcase of the K7M engine discussed below holds 3.5 liters of fluid. .

Anyone who decides to replace the "quick method" is recommended to watch the video.

From the factory, the 8-valve on Lada Largus will be filled with ELF SOLARIS RNX material. The viscosity of the material is 5W30. There was another option - LUKOIL Genesis RN 5W40. Renault pours ELF oil into its 8-valve valves: brand - Excellium NF, viscosity - 5W40. And this company recommends using a different material - ELF Evolution SXR 5W30.

Instead of "ELF SXR" is now "ELF 900 SXR"

According to the recommendations of the VAZ, the viscosity is chosen depending on the temperature: 0W30 for the North, 5W30 for Siberia, and there is also a viscosity class of 10W40. API quality level - any of the three: SL, SM, SN. Ash content according to ACEA - from A1 to A5.

Oil filter and its choice for 8 valves

Oil filters of the SOGEFI brand are supplied to Renault factories. All filters suitable for the K7M motor are marked as follows - 7700274177. And on the same lines, analogue substitutes are produced: LS218 (Purflux brand), PH11774 (FRAM), FT6129 (Fiaam).

Standard and advanced filter

There is also an improved version of the filter. It is designated by numbers 8200768913. List of analogues: Purflux LS932, Fiaam FT5902, FRAM PH5796. More full list.

Metal parts

The crankcase drain hole is closed with a metal plug. The part numbers for this part are 7703075348, 7703075210, 7703075347 and 7903075033. There is a washer under the plug. It is designated as follows: 110265505R, 8200641648, 7703062062.

Two gasket options

In the last, that is, in the third case, we are talking about a copper ring. Washers with rubber include the first and second articles.

Everyone who spins the cork without a washer, then let him take offense at himself. In general, the washer can be made of copper (d = 16.7 mm).

Instructions for changing the oil on an 8-valve engine (with photo)

Always warm up the engine before changing the oil. Then turn off the ignition and place the car on the flyover. It would be better to immediately remove the filler cap.

It remains to fill in new oil. But we will also change the oil filter.

How to get to the filter?

If the number of valves is 8, the oil change in the Lada Largus engine is carried out as follows: the waste is drained and new oil is poured. The filter is not replaced. And to change it, it will be enough to open the hood.

Space from radiator to engine

The filter housing is fixed next to the exhaust system casing. We take a puller, unscrew the filter.

The new filter is filled with oil by a third (70-100 ml). The rubber ring must also be wiped with oil.

Everything is ready for installation

The filter housing is screwed into the crankcase until it stops by hand. Here the recommended force is 15-17 N * m.

The process of filling and checking the oil level

We take a funnel and pour 3.3 liters of new oil through the filler neck of the motor. After closing the lid, we start. Let the motor run for 1-2 minutes.

Everything is bad here - the lamp is still on

If the “oil can” lamp goes out, it means that we were not mistaken with the volume. You still need to check the level though.

When the motor is stopped, it is necessary to wait 3-5 minutes. Then take out the control probe and look at the marks. The article numbers for Renault probes are 8200678386 and 7700273904.

Checking the oil level in the crankcase

Install the dipstick into the crankcase by pushing it in until it stops. If necessary, remove the filler cap and top up.

Technology Secrets

If there is no puller, but it was not possible to unscrew the filter by hand, you can do it simply: take a screwdriver, pierce the case, unscrew the part counterclockwise. Here the screwdriver is used as a lever.

The filter housing will have to be slightly damaged

The main thing is that the punch hole is closer to the bottom. All actions are carried out from under the hood.

We find the replacement period “by eye” - an example in the video

Many owners of Lada Largus cars try to take care of changing engine oil in a gearbox with 16 valves on their own. Oil change is required every 10-15 thousand kilometers or once a year, with a filling volume of 4.8 liters. Another 100-200 milliliters is required to fill the "new" oil filter, which is subject to change. Maintenance for the 16-valve Lada Largus unit is not provided.

What oil is ideal for Lada Largus

One of the main tasks is right choice engine oil, which should be suitable for a 16-valve engine. Motorists face the first difficulties even at the selection stage, as annoying mistakes are often made.

Important! The quality of engine oil has a significant impact on engine performance and durability.

If the wrong or low quality oil is used, there is a risk of a significant reduction in the life of the vehicle. Moreover, if the Lada Largus car is under warranty, you cannot use low-quality consumables, because, otherwise, the possibility of repairing the motor with the involvement of the warranty service will be lost.

In order for the Lada Largus oil change to be carried out correctly and successfully, it is recommended that you carefully read the service manual for the car. It is in this document that the parameters that the used technical fluid must have are indicated.

In this case, the substance must necessarily correspond to a certain level of viscosity, which is determined by the SAE standard:

• 5W40;
• 0W40.
• 0W30;
• 5W30.

If you conduct a thorough study of the available products, it becomes possible to understand that the best engine oils are offered by the following foreign and domestic manufacturers with an excellent reputation:

• Shell Helix;
• Lukoil.

It is important to understand that the viscosity grade of the engine oil used for Lada Largus must comply with the recommendations of the car manufacturer. Otherwise, the occurrence of problems when using the car will be inevitable.

Replacement is allowed to be carried out no earlier than after 15 thousand kilometers. If a vehicle has already undergone the first change, it is best to re-change the oil after 10 thousand kilometers.

Care should be taken to carry out the necessary procedure if the technical fluid used has lost its own properties or characteristics:

• the color turned black;
• deposits and sediments, a metal rash and other components appeared in the composition, indicating a significant deterioration in the quality of engine oil;
• the consistency has become very liquid, as a result of which it can be compared technical oil with ordinary water.

The use of consumables in case of such violations of properties will never turn into anything good and positive. In this regard, it is advisable to take care of the mandatory event in advance, because, otherwise, the internal combustion engine and the entire system may suffer.

Without fail, you need to take care of the availability of everything that may be required to complete the task:

• a canister with new and high-quality engine oil;
• working oil filter;
• set of wrenches;
• tetrahedron on "8";
• an old bucket needed to collect old oil;
• old rags.

Only after you have managed to take care of the availability of all the necessary attributes, you can begin to implement existing plans. At the same time, it is desirable that the oil change at the Lada Largus checkpoint be carried out correctly and in stages. The main task is to focus on technical regulation.

1. The car is initially driven onto a flyover or viewing hole. Such a location guarantees a high level of safety, as there is a stable placement and the complete elimination of undesirable risks associated with the instability of the machine.
2. The next step is to remove the engine crankcase protection. The pallet must be cleaned of dirt.
3. Raise the hood and unscrew the plug.
4. Loosen the drain plug a couple of turns. For this you need a quadrilateral. Then a container is substituted and the lubricant is drained.
5. The condition of the sealing masonry is checked to ensure that the drain mouth has a reliable design. If necessary, the sealing masonry is replaced.
6. After a while after the waste liquid has completely drained, the neck plug is allowed to be screwed back.
7. The oil filter must be replaced. In this case, the rubber part must be lubricated with oil. After that, the installation can be performed.
8. New consumable liquid is poured. Ideal the volume of oil for Largus is 4.8 liters, and this indicator is highly undesirable to exceed. Periodically check the level with a dipstick. After completing the task, the neck can be closed with a stopper.
9. At the final stage, the engine starts. It is advisable to leave the motor running for some time so that it disperses the lubricant throughout the system. When starting the engine, the emergency pressure lamp should stop burning. After that, the level of the lubricant composition is re-checked, and it should be in the middle between the minimum and maximum values.

Change the engine oil yourself car Lada Largus is extremely easy. The procedure only takes about half an hour. After 2 hours of sludge, the vehicle is allowed to operate in the same mode.