Mini tractor made from a walk-behind tractor. Homemade mini-tractor from a walk-behind tractor: step-by-step instructions How to convert a bison walk-behind tractor into a mini-tractor (drawings)

A mini-tractor made from a walk-behind tractor is the optimal solution for cultivating small plots of land. Not every person can afford to buy a factory model of a mini-tractor, so you have to improvise.

It is much easier and cheaper to buy a walk-behind tractor and convert it into a homemade mini tractor. You can do this yourself, fortunately there is nothing complicated about it. Let's look at the key aspects of converting a walk-behind tractor into a mini-tractor.

Choosing a walk-behind tractor

The walk-behind tractor that you are going to convert must meet certain criteria, otherwise the mini-tractor will not fully perform its operating functions. It is necessary to pay attention to the following nuances:

1. Power. The larger the area you plan to process, the more powerful the walk-behind tractor should be.
2. Type of fuel. It is best to choose models that work on diesel fuel. Diesel engines cope well with processing large areas and consume fuel more economically than their gasoline counterparts.
3. Weight. If a walk-behind tractor is purchased as a separate agricultural implement, then it is necessary to choose models with low weight. They are more manageable. In our case, we should give preference to more massive products. After all, a homemade mini tractor must cultivate the soil, and if the machine is light, it will not cope with hard soil.
4. Price. You should not buy expensive walk-behind tractors. After all, a mini-tractor is converted from a walk-behind tractor in order to save money, so you shouldn’t spend money purchasing an advertised brand. It is better to give preference to domestic producers.

The following walk-behind tractors fit the above parameters:

• Agro;
• Neva;
• Centaur;
• Bison

It is worth noting that for these models you can purchase ready-made kits for converting them into a mini-tractor with your own hands.

Of the above models, only the Agro walk-behind tractor has design flaws . This is reflected in the lack of fracture strength of the axle. This defect does not affect the operation of the walk-behind tractor in any way, but when converting the unit into a homemade mini-tractor, the load on the axle shafts will increase significantly. Therefore, you will need to strengthen the problem unit of the walk-behind tractor. This can be done by installing wheel reducers.

Options for making a mini-tractor with your own hands

Motoblock "Centaur"

This agricultural unit belongs to the category of professional equipment; accordingly, it will make a mini-tractor with good performance. The 9 horsepower diesel engine plays a key role.

To convert this walk-behind tractor into a mini-tractor with your own hands, it is enough to make a frame from a metal profile, install an additional wheelset and a seat.

Homemade mini tractor from the Centaur walk-behind tractor can be equipped with a trailer for transporting small-sized loads, a single-share plow and a moldboard.

Motoblock "Bison"

As in the previous case, the device is equipped with quite good power plant, which runs on diesel fuel. To make a mini-tractor based on the Zubr walk-behind tractor, you will need the following elements:

1. Hydraulic system. It is necessary for the tractor to operate with attachments.
2. An extra pair of wheels. They can be removed from passenger car mobile.
3. Brake system and steering.

Motoblock "Agro"

The mini-tractor from this model requires a more serious approach. In addition to all of the above, you will need to strengthen the drive axle shafts with wheel reducers. Alternatively, you can try a rear-mounted engine, this will distribute the load more evenly.

General assembly instructions

The process of converting a mini-tractor from a walk-behind tractor is the same for all the models listed above. In order not to repeat the same information every time, we decided to separate it into a separate block. The exception is a homemade mini-tractor based on the MTZ walk-behind tractor, but we’ll talk about it a little later.

Before starting work, you need to prepare the necessary parts and tools. For convenience, you can purchase a ready-made kit for converting a walk-behind tractor into a mini-tractor. The purchase will cost you approximately 30,000 rubles. From the tool you may need:

• welding machine;
• electric drill with a set of drills;
• wrenches and screwdriver;
• grinder and discs for cutting metal;
• fastening element (bolts and nuts).

Frame

First you need to supplement the supporting structure, because you will need to install an additional pair of wheels. To do this you will need metal corners or a pipe.

The cross-section of the pipe does not play a big role, the main thing is that it can withstand the expected loads. You can also approach the thickness of the walls creatively, because excess weight will only increase the tractor’s grip on the road and will serve as a good help when performing arable work.

The blanks for making the frame are cut with a grinder and fastened together with bolts or electric welding. You can combine the connection. For example, connect the elements together with bolts and additionally weld the seams.

To make the frame a truly reliable structure, you can install a transverse beam, which will serve as an additional stiffener.

It is recommended to mount directly to the frame attachment to work with additional equipment. The hitch can be attached to both the front and rear of the frame. If a homemade mini tractor will work with trailed equipment, a towbar is welded to the rear of the frame.

Chassis

For the front wheels, you can buy two ready-made hubs with brakes. The front one is attached wheelset as follows: take a piece of metal pipe that fits the width of the front axle. Wheel hubs are attached to this pipe.

Drilled in the center through hole, through which fastening to the front frame is carried out. After this, steering rods are mounted, which are connected to the frame through a worm gear. After securing the gearbox, the steering column is installed.

The rear axle is mounted on bearings pressed into bushings. A pulley is installed on the axle to transmit torque from the engine. The wheels can be used from an old passenger car or left “original”, adding another set of wheels from another walk-behind tractor.

It is worth noting that the recommended wheel radius is 12-14 inches. If you install wheels of a smaller radius, the mini-tractor made from a walk-behind tractor will bury its nose. Installing large wheels will negatively affect the handling and maneuverability of the machine.

Engine

Usually power unit installed on the front of the frame. Thus, the mini-tractor maintains the necessary balance when working with trailed equipment. A mounting system is made at the engine installation site.

Remember that the power take-off shaft must be aligned with the pulley on the rear axle of the machine. The force is transmitted through a belt drive. To facilitate adjustment and tension of belts, it is recommended to make the engine mount floating.

Additional equipment

Having assembled the main structure, install braking system and a hydraulic distributor for working with attachments. If a homemade mini-tractor will move on the roads, it makes sense to install headlights and side lights. This will avoid problems with traffic police officers and make it easier to work in the dark.

To give the mini-tractor a more attractive look, you can equip the equipment with cladding elements and a sun canopy. Additional tuning done based on personal preference.

After assembly, the mini-tractor must be run-in and you can start working.

DIY mini-tractor based on an MTZ walk-behind tractor

There is a rather original way to convert a mini-tractor from an MTZ walk-behind tractor. This walk-behind tractor is equipped with a two-cylinder diesel engine, so during operation the center of gravity shifts to the front. This significantly complicates the workflow. You can fix the problem as follows:

1. The walk-behind tractor is switched to operating mode with a mower.
2. The front platform is completely dismantled.
3. It is installed in its place using bolts front wheel from the motorcycle, along with the steering wheel.
4. In the niche for installing the steering rod, it is located in the upper part of the frame, an adjusting rod is attached. This gives the structure additional rigidity.
5. The mount under the driver's seat is welded to the platform using electric welding.
6. An additional platform for the hydraulic distributor and battery is welded next to the engine.
7. An additional steel frame for the hydraulic system is installed at the rear.
8. A handbrake is mounted on the front motorcycle wheel.

Thus, you get a compact three-wheeled mini-tractor made by yourself.

It is easier and more convenient to cultivate dacha and personal plots of land with the help of a small tractor. And it doesn’t matter if you don’t have enough money to buy a factory “iron horse” - you can make it yourself from an inexpensive walk-behind tractor. Moreover, when you have an interest in technology, engineering abilities, the necessary equipment and tools, this will not be difficult at all. The main thing is to understand the technical aspects, prepare for the transformation and choose the right walk-behind tractor.

Preparing to create a homemade mini tractor

The process of creating a homemade mini tractor begins with drawing up a drawing, kinematic diagram of the future “plowman” and preparation necessary materials, tools, equipment. If you have the skills, you can develop a diagram yourself to demonstrate the mechanisms and components of the tractor; if not, find suitable option on the Internet or use the example presented here.

As for the parts and components involved in the modernization of the walk-behind tractor, you can use a purchased factory kit to convert it into a mini tractor. But this option is not suitable for those who want to, for example, break a 4x4 and at the same time save a lot.

So, to create a homemade tractor you will need:

• Tool set;
• Welding equipment;
• Drill with a set of drills;
• Metal pipes, channels;
• Fasteners, hardware (bolts, nuts);
• Grinder, discs for working with metal.

Also, in order to make a tractor with your own hands, you will need two suitable wheels, a hitch, a driver’s seat, a steering mechanism, pedals and, of course, a walk-behind tractor with sufficient weight and power. It is better to opt for a heavy-duty unit with a diesel engine (the Zubr, Neva, Agro, and Scout models are good options). This will make it possible to obtain, as a result of the alteration, a home-made, but productive mini-tractor capable of effectively performing various agricultural operations. You will probably want it to perform not only agricultural functions, but also be able to pull a trailer.

The weight of the selected unit must correspond to the condition of the soil on which it is planned to use the homemade product. If it is compacted and dry, then the future mini tractor is unlikely to cope with the tasks assigned to it. Therefore, the harder the soil, the heavier the walk-behind tractor will be needed. And the power of its engine should be correlated with the area land plot, where agricultural work will be carried out using a motor tractor. So, the larger the plot, the higher this parameter should be.

How to make a frame

After preparing the tools and components necessary to create a mini tractor, they begin to “reshape” the frame of the walk-behind tractor in order to adapt it, in accordance with the drawing, to an additional pair of wheels. platform of the future homemade car can be made all-metal or fracture using channels or profile metal pipes. Longitudinal and transverse spars are easy to make - they are cut with a grinder and connected by electric welding or fasteners. For greater reliability, bolted connections are combined with additional welding of the seams.

When transforming a cultivator into a mini-tractor, a breaker is often used, consisting of two independent semi-frames connected to each other using hinges. Thanks to this design, all four wheels of the tractor are almost always in contact with the ground, and there is practically no hanging out when operating the homemade product on an uneven surface or slippery road. This allows you to increase the stability of a mini tractor made from a walk-behind tractor, improve its maneuverability and cross-country ability when carrying out arable and transport works.

An attachment device is mounted to the front or rear section of the prepared frame according to the diagram, which will allow the tractor to make possible job with auxiliary devices. You can weld a towbar right at the back for towing a trailer - this will expand even more functionality homemade motor-tractor obtained from a walk-behind tractor.

Installation of the chassis

Upon completion of installation, the mounting devices are installed on both axles (front, rear), and the wheels are already on them. The ones that came with the walk-behind tractor (Scout, Zubr, Neva) are usually attached to the rear axle, and wheels from a passenger car or some kind of agricultural machinery are mounted to the front axle. It is important that they have a deep tread - this will make the homemade mini tractor a high-cross-country vehicle with improved wheel grip on the ground.

To equip a homemade tractor with a full front chassis buy hubs assembled with a brake system and preferably complete with steering rods, steering wheel, gearbox and steering column. They can also be remade by removing them from used passenger vehicles.

The front wheels are attached to the mini tractor in this way:

• Select a metal profile pipe that matches the thickness of the front axle of a homemade tractor;
• Wheel hubs are attached to the ends of the profile;
• The structure with hubs is fixed to the front frame directly in the center;
• Mount the steering rods, and then align them with the steering gear;
• The gearbox is fixed to the frame;
• Install the steering rod steering wheel;
• Adjust the steering column.

Sometimes the tractor's front suspension is supplemented with spring shock absorbers to provide more comfortable working conditions. After the steering column has been assembled according to the drawing, you need to install the rear wheels.

The rear axle of the cultivator is mounted on bearings tightly pressed into spherical bushings. A pulley is mounted on it, which will transmit torque from the engine to the rotating components. You can leave the rear wheels of the breaker without a differential - this will simplify the design and minimize slipping of the future mini tractor when operating on loose soils.

The optimal diameter of tractor wheels is 30-36 cm (like the Scout T-15 model). If homemade diesel unit put it on smaller wheels, it will simply tilt forward. Installing large wheels will make the machine uncontrollable and impair its maneuverability, especially when working with a trailer. Once the installation of the wheels and steering column is complete, the assembly of the main unit of agricultural machinery - the engine - begins.

Engine and hydraulic installation

The most profitable option for converting a walk-behind tractor into homemade tractor considered single cylinder diesel engine with water cooling - this is usually installed on Chinese walk-behind tractors of the Scout, Zubr and Russian Neva brands. A single-cylinder diesel engine is economical, so operating a mini tractor based on it will not be expensive. It is typically placed on the front of the frame, allowing the small tractor to maintain optimal balance when operating with additional tools. A fastening system is installed at the location of the motor, which is best made “floating” (sliding) to simplify the adjustment and tension of the belts.

The transmission of force from the engine to the rear wheels of a homemade tractor is organized using a belt drive. Transfer case The PTO, like the gearbox, can be used from a decommissioned GAZ-53 car. The homemade power unit is mounted in such a way that the PTO pulley is located in the same plane as the pulley located on the rear axle of the mini tractor. At the same time, they mark out a place for the clutch pedal. The belt drive is covered with a protective cover to avoid slipping during operation and to make its service life longer.

After completing the main work, a hydraulic lift is installed on a homemade mini tractor with an engine from a walk-behind tractor. The hydraulic conversion kit must include oil pump, oil tank, hydraulic cylinder and distributor. All components of the system are connected by flexible oil-resistant hoses. It is advisable to make the hydraulics with a floating mode - this will ensure full operation of the motor-tractor hitch.

Then the driver’s seat is installed, as well as headlights and dimensions if the mini tractor is planned to be driven on roads. They will ensure safety when operating vehicles at night and will allow you to avoid problems with demanding road patrol officers.

Installation of the brake system and electrical equipment

After installing the engine, they begin to install an equally important component of the mini tractor - the brake system. In the store you can buy new brakes for a homemade unit or use standardized parts from a passenger vehicle.

First, determine the location (using the layout diagram) where the brake pedal will be located in the alteration. The pedal mount and the main brake cylinder are mounted on the designated plot. The cylinder is then connected with hoses to brake drums, located on the front wheels of the converted tractor.

Immediately after this, the brake system is checked for leaks and if it is broken, everything will have to be redone. To avoid ridiculous mistakes, it is better to use a visual drawing that shows all the main components of the tractor. To control, the system must be pumped and any remaining air removed. This will make it operational and provide proper functionality. You can also supplement the system parking brake.

The next stage of self-conversion of a walk-behind tractor into a full-fledged mini tractor is connecting electrical equipment and displaying sensors on the instrument panel. It is recommended to do this for the convenience and safety of transport operation. The panel displays a temperature meter, a liquid cooling indicator, an ignition key, an oil pressure sensor and a fuel level sensor in the gas tank. If desired, a homemade tractor is supplied sound signal, brake lights and direction indicators.

Additionally, agricultural machinery can be equipped with cladding elements and a canopy. This will give the minitractor an attractive appearance and make the operator’s work more comfortable. After completing the process of modernizing the walk-behind tractor, you should run-in the home-made mini tractor so that the parts “grind in” and improve the lubrication of the mating surfaces.

Advantages of homemade tractors from walk-behind tractors

A mini tractor converted from a walk-behind tractor will be very useful on the farm! It definitely needs to be done to turn routine agricultural work into tireless and interesting activities. A homemade tractor, unlike a walk-behind tractor, will take on the main load, and the person will only have to monitor the process and properly drive the vehicle. A homemade small tractor is a compact unit that is economical to operate and maintain and does not require a separate garage, which is also a big plus. It will not create problems with spare parts - they can be found on sale at affordable price in almost any specialized store that sells walk-behind tractors of the brands Scout, Neva, Zubr and others.

The advantages of owning such a unit are obvious. Unlike a walk-behind tractor, it will allow:

• Expand functionality;
• Facilitate the operator's work;
• Realize traction potential.

Using skills, you can use a conventional motor cultivator with disabilities make a multifunctional and efficient mini tractor. Maneuverable, compact - it is able to work even in densely planted areas, between bushes and trees, as well as in limited local area without damaging paving slabs and asphalt surfaces.

Making a mini tractor from a walk-behind tractor means purchasing agricultural machinery with the widest functionality. Together with it, you can use a variety of attachments: cultivator, potato planter, milling cutter, harrow, rotary mower, plow, hillers, etc. And if you equip it with a hydraulically driven stacker, then you can operate a homemade tractor also as a hay thrower or a crane. Thanks to its practical design, working with such a homemade product is simple, comfortable and safe. A homemade mini tractor is better than the most expensive walk-behind tractor and cheaper than a heavy tractor.

For a true owner, there is no limit to perfection. As soon as a summer resident acquires a utility device in the form of a walk-behind tractor, an irresistible desire immediately arises to turn it into something much larger and functional. Converting a walk-behind tractor into a mini-tractor is the most common transformation that summer residents-designers implement. After all, not everyone can afford to buy a mini-tractor, but in terms of the functionality it receives, it will be much superior to the same walk-behind tractor!

The question, of course, is rhetorical, but first it’s worth deciding what and, most importantly, how we will redo it? That is, we start, as always, by preparing a sketch and drawing of the main components and elements of the unit.

The mini-tractor is a self-propelled vehicle, which has all the necessary nodes inherent
to such. This is the platform on which the power unit is installed and to the base of which all additional components and elements are attached, 4 wheels, steering, brake system, pedals, gearbox, electrical wiring, driver's seat. When converting a walk-behind tractor into a mini-tractor, all these missing components will need to be purchased ready-made or built independently. As a result of the conversion, you need to get more than just a four-wheeled vehicle. We need a full-fledged agricultural machine, capable of not only cultivating the land in the same way as a walk-behind tractor, but also being able to do much more! After all, if after the conversion the functionality of the unit does not expand, what’s the point of starting everything?

Necessary tools and equipment

Before proceeding directly to the conversion of the walk-behind tractor, you need to decide on the minimum list of tools that will be needed during the work process:

In order to turn a walk-behind tractor into a full-fledged mini-tractor, you will need to acquire the following:

• metal profile pipe for the manufacture of frames and supporting structures;
• wheels;
• front wheel hubs with brake system;
• steering wheel, steering rod, steering rods;
• worm steering gear;
• transmission;
• footrests with pedals;
• brake fluid container;
• driver's seat;
• instrument panel;
• wheel protection (fenders);
• additional attachments with which it is planned to expand the functionality of the mini-tractor.

Frame structure

The first thing to start with when converting a walk-behind tractor is the construction of the main supporting structure of a mini-tractor or
frames To make it, you can use a metal profile pipe with a cross section of 20 by 40 mm or 40 by 60 mm and a wall thickness of 2.5–3 mm. The choice of the diameter of the initial tube is not fundamental. If somewhere in the bins there is a profile pipe of a slightly different cross-section and in sufficient quantity, you can safely use it.

Cutting blanks to create a frame is done using a grinder. After all the components are prepared, they must be combined into a single structure. To do this, they are compared on a flat horizontal surface using a square and fixed using clamps. Next, using a welding machine, they are grabbed from several sides to each other. After the frame blanks are connected, they once again check the correctness of the geometry of the entire structure and finish welding all the seams. Places that will account for increased load or vibration, needs to be further amplified.

Useful advice. Don’t worry if you suddenly can’t fully calculate the entire structure of the mini-tractor frame. Start with just a basic wheel frame, based on the overall length of the mini tractor frame. The remaining parts can be added during the manufacturing process.

In the rear as well as the front part of the frame, it is necessary to provide the possibility of attaching auxiliary attachments (ploughs, cultivators, mowers, etc.). Additionally, it is worth installing a towbar at the rear, which will allow you to tow a trailer with a payload.

Installation of the front chassis

After the manufacture of the main frame element is completed, it’s time to begin installing the chassis. Due to the simplicity of organizing the design and doing it yourself, some suspension components can be simplified (in particular, the installation of shock absorbers and springs). And although working on such a mini-tractor may seem harsh, simplifying the design will eliminate many technical hassles.

The front suspension can be installed as follows. At the car market, among used spare parts, you need to purchase two front wheel hubs with a brake system assembly, if possible with a set of steering rods, a gearbox, a steering column and a steering wheel. They will be used to make the front chassis of a mini-tractor.

First, select a section of profile pipe corresponding to the width of the front axle. Next, the wheel hubs are attached to the ends of the prepared tube. Then we find the center of the axis, drill a hole in it and, using a bolt, fasten it to the end in the center (longitudinal axis) of the frame. Thus, being rigidly fixed to each other on the axle, the front wheels of the mini-tractor can freely tilt relative to the entire body.

Useful advice. If you use hubs from a passenger car for the front wheels, then there is no need to invent anything with tires later. All you have to do is stock up on used tires of the right size.

Next, the steering rods are installed, matched with the worm steering gear and secured to the frame. After the gearbox is secured, the steering rod and steering wheel are mounted. It is worth considering that during the installation of the steering rod, it may have to be additionally fixed. When the steering column is assembled, you can begin installing the driver's seat, as well as rear wheels.

Rear chassis installation

The installation of the rear wheels has its own characteristics, since this is where the transmission of torque from the engine will take place. To simplify the design, the wheels can be made rigidly coupled, that is, without installing a differential. This solution has several advantages:

• firstly, the design of the mini-tractor is significantly simplified;
• secondly, a rigidly fixed rear axle will minimize slipping of the tractor when working on open ground.

It is worth remembering that with a rigidly fixed rear axle It will definitely be difficult to move on asphalt, especially when turning, since such equipment will contribute to increased tire wear.

The rear axle is best secured using bearings rigidly pressed into the bushings. On the axis itself, it is necessary to pre-install a pulley or sprocket to transmit force from the engine. For rear wheels, it is better to purchase special models for a mini-tractor, which will have an increased size and a large tread pattern. With such wheels it will be convenient to move on plowed land.

For protection against dirt, water and stones, the front and rear wheels it is necessary to cover it with protective wings, which you can either make yourself from a galvanized sheet, or purchase a suitable ready-made option.

Engine installation

Engine installation internal combustion produced in the front of the mini-tractor. This is done in order to change the redistribution of weight and create additional weight in front. After all, the main load at the rear will be created by the towed equipment. The type of fastening and installation nuances depend on the specific walk-behind tractor that is planned to be converted, as well as the engine on it.

Before installing the motor on the frame of the mini-tractor, a mount is installed. In order to be able to adjust the tension force of the belt drive, the engine mount to the frame can be made sliding by creating appropriate slots for the bolts.

Useful advice. Among the engines installed on a mini-tractor, preference should be given to those that have
water cooling. If you choose an air-cooled motor, there must be sufficient air circulation to ensure adequate cooling.

It is recommended to transmit torque from the engine to the rear wheels using a belt drive. The motor must be installed in such a way that the power take-off shaft pulley is on the same axis with the pulley mounted on the rear axle. This will prevent the belt drive from slipping off during operation, as well as its increased wear. After installing the belt drive, it must be covered with a protective cover along its entire length.

If the engine has a gearbox installed, it should be possible to change gears from the driver's seat using special rods. It is also necessary to provide a place for attaching the clutch pedal.

Brake system installation

After the engine is installed, the installation of the brake system begins. As parts for it, you can use standardized parts of a passenger car.
The first step is to determine the location of the brake pedal. The pedal mount should be installed in this place, as well as the brake master cylinder. After this the connection is made brake cylinder to the brake drums of the front wheels using metal and rubber hoses. Next, the brake system must be checked for leaks and bled to remove residual air and ensure proper functionality.

Installation of electrical equipment

Depending on type installed engine You can display the ignition key, coolant temperature sensor, and fuel level indicator in the gas tank on the instrument panel. If you plan to move and work on a mini-tractor at dusk or at night, you need to install a headlight in front, and additional side lights in the back and on the sides. Also, if the possibility of traveling on roads as part of the main traffic flow of cars is not excluded, the mini-tractor must be equipped with brake lights and direction indicators.

Connecting additional equipment

A bucket can be installed in the front part of the mini-tractor as an auxiliary equipment, and in the rear part -
the whole range of agricultural machinery for cultivating land. Additionally, it is recommended to equip it with a hydraulic pump and hydraulic cylinders. With their help, it will be possible to lower and raise attachments and perform other manipulations. If an additional power take-off shaft is provided from the engine (for example, using an additional cardan transmission), then it will be possible to connect not only static, but also moving, dynamic equipment. This will significantly expand the scope of application of the mini-tractor.

Conclusion

With a little skill and a great desire, in just a few days a walk-behind tractor can be turned into a full-fledged mini-tractor, which will become an indispensable assistant around the house and household. Using a huge additional arsenal of mounted and trailed equipment, a mini-tractor can be turned into a universal agricultural machine!

Video from Youtube about converting a ZUBR walk-behind tractor into a mini tractor.

Nowadays in rural areas Private farms and farmsteads predominate, in some cases people try to work for themselves and not for the master, cultivate the land, raise livestock, chickens, geese, and so on. Of course, it’s not easy to do all this manually, since ancient times people have resorted to the help of horses and oxen to plow the land, in Soviet times there was a powerful agrotechnical complex, and with the collapse of collective farms people are engaged in individual farming, again mechanical help is required in difficult work, and the fathers of engineers We have developed a walk-behind tractor that is in demand among rural residents. A universal machine for farmsteading, you can do all the work: plowing, cultivating, planting, mowing, watering, transporting loads. High performance with low energy consumption, a liter of gasoline is enough for one hour of work. A fairy tale and not a unit, but our craftsmen went further and improved the walk-behind tractor

Tools: welding machine, grinder, hammer, chisel, set of keys, pliers, screwdriver, drill

Materials: corners, square and round pipes, roofing metal, steering column, steering wheel, rod, rods, hubs, rear axle from a Muscovite.