How to fill oil in the Nexia gearbox. We change the oil in the Daewoo Nexia gearbox ourselves. How much oil to pour into the Daewoo Nexia box

It is filled in for the entire period of operation of the car, but does not specify in any way exactly how long this service life should be and how to check whether it is over or not. Therefore, in order to avoid serious financial costs for repairing the gearbox, it is recommended to replace it every 100 thousand km. mileage If you have difficulty shifting gears in cold weather, you can change the oil in the box even before the mileage reaches 100 thousand.

It is almost impossible to check what exactly is poured into the gearbox at the factory, but most often this oil turns out to be mineral oil, which thickens quite strongly in winter. When planning a replacement, it is recommended to purchase synthetic or semi-synthetic gearbox oil.

From time to time, at least once every 15 thousand km. mileage, you should check the lubricant level in the gearbox. Gearbox design Daewoo Nexia There is no provision for lubricant replacement throughout the entire service life. However, sometimes the need for replacement still arises - in the case of a gearbox repair, when switching to a lubricant with a different viscosity, and in other similar situations. When planning a replacement, it is advisable to drain the old lubricant in a warm and fluid state, that is, within 10-15 minutes from the end of the trip.

Which one should I use?

In case of box Daewoo gears Nexia is best to use a synthetic or semi-synthetic lubricant. The manufacturer recommends using SAE 80W GL-4 transmission oils, and if the vehicle is operated in frosty climates, when the air temperature does not rise above -30° for a long period, the use of 75W90 GL-4 is recommended.

Accordingly, the Daewoo Nexia gearbox can be filled with either mineral oil 80W90 GL-4, and synthetic or semi-synthetic 75W80, 75W90, 80W85 GL-4. One of optimal options can be considered 80W GL-4. Synthetic lubricant 75W80 is also excellent, especially in winter. In summer, this oil leads to noise in the gearbox, so it is still better to use oils recommended by the manufacturer.

The volume of oil that must be poured into the gearbox is 1.8 liters.

Gear oil for gearbox LIQUI MOLLY (SAE 80W GL-4)

Tools

In order to replace the fluid in the gearbox of a Daewoo Nexia, you will need the following tools and accessories:

• jack;
• syringe;
• 13 mm socket head;
• 17 mm socket head;
• 19 mm wrench;
• oil directly;
• transmission pan gasket;
• container for draining used lubricant.

In order to choose the right gasket, it is first recommended to inspect the transmission pan from below. This is due to the fact that there are two types of pallets, having 10 or 11 holes - the number of holes must be checked before purchasing a gasket. In addition, you don’t have to buy a gasket, but remove the pan and cut it out yourself from paronite, or simply replace it with a sealant, which in practice copes well with the task.

Instructions

Changing the oil in the gearbox is carried out on an overpass or pit. The replacement procedure includes the following steps.

1. If there is engine protection, remove it.
2. Using a 10 mm socket, loosen the transmission pan bolts.
3. We tighten the bolts in the front part of the pan and place a wide container under the drained oil.
4. After draining all the lubricant, completely remove the pan. In this case, even if the gasket does not break, it is recommended to replace it.
5. Usually only 1.5 liters of oil is drained, and 200-300 g continues to remain in the crankcase. To completely drain, you can raise the front left wheel to the maximum height possible with a standard jack.
6. Using a 13 mm socket, unscrew the oil level plug on the right side of the gearbox under the inner CV joint. Then we thoroughly rinse the plug itself from the inside, as well as the loose magnet located in its cavity.
7. After waiting until oil stops dripping from the gearbox, we install the pan in place, thoroughly cleaning its seat from old grease and gasket residues. The pan is installed with a new gasket or sealant, without tightening the control plug.
8. Next, you can fill in new gearbox oil. To do this, twist the breather in the upper part of the gearbox, next to the selector mechanism. Remove the plastic cap from the breather and unscrew it using a 19mm wrench.
9. For convenience, insert a funnel into the breather hole and slowly add oil until it begins to flow from the plug hole, then tighten the control plug. As a result, about one and a half liters of lubricant is poured.
10. If the front left wheel was lifted to completely drain the fluid, then after closing the plug, add oil to the nominal volume. Otherwise, there is no need to perform additional filling.
11. All that remains is to screw the breather back to its original location.

At this point, replacing the fluid in the Daewoo Nexia gearbox can be considered complete. There is nothing complicated about this, all that remains is to check and make sure that the gears change easily enough, regardless of the time of year.

Video instruction from TANTOA

If you have any questions, or you couldn’t understand the text instructions, we suggest watching our video.

Daewoo Nexia– a popular car model from a Korean manufacturer. Widespread and popular both in Russia and in the former CIS. One of the main reasons for popular recognition is the low price with good technical specifications and the reliability of this sedan.

Brief history of the model

This middle-class car model was released back in 1986. It is noteworthy that it was developed by German engineers from the Opel concern. The then popular Opel Kadett E was used as a prototype. The car was developed specifically for developing countries. After modernization by the Daewoo company, in 1995 the car began to be sold on the market in the countries of the former USSR as Daewoo Nexia. In its homeland, Korea, this model was called Daewoo Cielo.

Daewoo Nexia differed, first of all, low cost– at the level of domestic VAZs with front-wheel drive. The machine also had good reliability and ease of operation, outperforming in these indicators domestic cars and not inferior to foreign ones in its class. Replacing parts, even if they failed, was quite affordable. These indicators were the main reason for the great popularity of this car.

Whatever advantage this car had over Russian VAZs, it dried up over time. Daewoo Nexia was produced until 2013, after which it was replaced by Daewoo Gentra.

Daewoo gearboxes

Two types of gearboxes were used in the design of the car:

• manual 5-speed;
• automatic with 4 steps.

The production of Daewoo Nexia was established on the territory of Uzbekistan with mechanical boxes transmission What kind of oil is used to operate them? One that meets API GL4 SAE 80W90 and API GL4 SAE 75W90 standards. Automatic transmission Only Korean hatchbacks produced from 1994 to 1997 are equipped. This box uses only Dextron II gear oil.

It is noteworthy that, according to the instructions of the Korean manufacturer, the lubricant in the gearbox cannot be replaced and must be used throughout the entire period of operation - this is approximately 200 thousand kilometers. It is only necessary to periodically check its level and top up if necessary.

Only a replacement is provided for regions where severe frosts are observed (below 30 degrees) - in cold weather the “mineral water” thickens. In order to save on production, mineral oil is poured into the box. Therefore, it is advisable to replace it with a synthetic or semi-synthetic one - preferably immediately, or after a run of about 100 thousand km.

Do not forget that during operation it is necessary to check the oil level - both in the engine and in the transmission. If after 10–15 thousand kilometers the lubricant level in the transmission is insufficient, you should fill in a substance with exactly the same characteristics. Subsequently, after replacement, it is advisable to add exactly the lubricant that is already in the mechanism.

Preliminary preparation

If you want to fill synthetics yourself, you need to check how many available materials are available. For this purpose, you will need 10, 13 and 17 socket wrenches, as well as a 19 mm wrench. In addition, you need a jack and a container into which the waste substance will be drained. You will need a large syringe or oil funnel.

It would be better to replace the pan gasket in the transmission. In order to purchase a new one, you should look under the car and see how many holes there are in the pan. There should be 10 or 11 of them; a new gasket should be purchased for their number. The most important thing is synthetic or semi-synthetic with a volume of 1.8 liters. What oil should I buy? It must meet the standards 80W85 GL-4 (optimally) or, as a replacement, 75W80, 75W90.

The Daewoo Nexia car appeared in the vastness of our country in the second half of the 90s of the 20th century. It immediately gained popularity among Russian car enthusiasts, since it was developed by specialists from the German company Opel on the basis of the extremely popular car in the late 80s. Opel models Kadett E specifically for developing markets.

The distinctive features of this car were its relatively low price, at the level of front-wheel drive models of the Volzhsky Automobile Plant, high reliability compared to domestic cars the same years of production and low operating costs relative to other foreign cars. However, over time, Daewoo Nexia began to become obsolete and lose its position in automotive market our country to new Volzhsky models automobile concern, and therefore in 2013 it was replaced by more modern model Daewoo Gentra.

To extend the life of trouble-free operation of the Daewoo Nexia, it is important to change it on time consumables and operating fluids. Changing the oil in the engine and gearbox (gearbox) is not a complicated procedure and can be done without the help of specialists.

Necessary clarifications

Depending on the country of production, Nexias were equipped with 2 types of gearboxes.

1. 5-speed manual.
2. 4-speed automatic.

Sedans produced in the Republic of Uzbekistan were equipped with manual transmissions. IN manual gearboxes Daewoo Nexia must be filled with transmission lubricants that meet the following standards.

1. API GL4 SAE 80W90.
2. API GL4 SAE 75W90.

It should be noted that, according to the manufacturer’s idea, the lubricant resource poured into the Daewoo Nexia gearbox on the conveyor should be sufficient for the entire life of the vehicle. This corresponds to a mileage of 250,000 km, after which the oil needs to be changed. According to the instructions, every 15,000 km it is necessary to check the transmission level and top it up if necessary.

At the same time, according to the recommendations of the manufacturer, changing the oil in the Nexia gearbox is mandatory if the car has been operated for a long time at temperatures below -30 degrees Celsius. Therefore, in the northern regions of our country, changing the gearbox oil is usually carried out immediately after purchasing a car.

3- and 5-door hatchbacks produced in the Republic of Korea between 1994 and 1997 were equipped with automatic transmissions. Such units can only be filled with Dextron II gear oil. The Nexia automatic transmission has a reusable oil filter. When replacing the lubricant, it can be cleaned and put back.

List of required tools:

• socket wrench 17;
• socket wrench 13;
• a special funnel-oiler or large syringe;
• basin;
• old toothbrush.

Before carrying out the procedure, you must drive 10 km, drive the car into a pit and install it on hand brake. Changing the oil in the gearbox is carried out as follows.

1. We unscrew the plug of the control hole and place a basin under it. The inspection hole is located on the side of the gearbox housing.
2. Remove the dirt cap from the filler plug. This hole is located on the intermediate gearbox housing.
3. Loosen and unscrew the filler plug. At the same time, we clean it from dirt.
4. We climb under the car, place a basin under the gearbox housing and partially unscrew 10 or 11 (depending on the type of gearbox) bolts securing the oil pan.
5. After the transmission has finished draining, remove the pan and clean it and the gears from visible dirt with a toothbrush.
6. We install the pan back and at the same time change its gasket. Tighten all the bolts.
7. After this we move to engine compartment and using a funnel or syringe, fill in new oil until it flows out of the control hole.
8. We clean the control hole plug from dirt and screw it in until it stops.
9. Screw the filler plug into place and put the dirt cap on it.

All. The automatic transmission oil is changed in the same way. The only difference is that, in addition to the procedures described above, after removing the pan, the oil filter is removed, cleaned of dirt with a toothbrush and acetone and installed back.

Replacing engine lubricant

As you know, Nexias were equipped with 4 types of power units:

1. G15MF.
2. A15MF.
3. A15SMS.
4. F16D3.

The first 3 had a volume of 1.5 liters and were installed only on Nexia 1 and 2 generations. The latest engine has a volume of 1.6 liters and is now installed on Daewoo Gentra cars. Changing the oil in the F16D3 engine is carried out in the same way as in 1.5-liter power units.

Along with the oil, the oil filter must also be replaced.. In addition, when carrying out this operation, it would be a good idea to check the oil pressure sensor located near the crankshaft pulley, as it quite often fails. List of required tools:

• wrench 19;
• slotted screwdriver;
• funnel-oiler;
• jack;
• bucket;
• multimeter

The Daewoo Nexia oil sump holds about 5 liters of lubricant, so you should prepare a large bucket. Before carrying out the operation, we warm up the engine, drive the car into the pit and put the handbrake on. The algorithm of actions is as follows.

1. Unscrew the drain plug and place a bucket under it.
2. When the oil stops draining, jack up the right and left sides of the car alternately.
3. We screw the plug back, and be sure to change the copper sealing washer.
4. We pierce the oil filter with a slotted screwdriver closer to the edge (away from the engine).
5. We clean and check the mobility of the anti-drainage valve.
6. Fill the new oil filter halfway with new motor oil, lubricate its O-ring and screw the filter to the cylinder block by hand.
7. We check the oil pressure sensor: to do this, unhook the wiring harness from it and connect one contact of the multimeter instead of the wiring, and the other to the sensor body and turn on the network dialing mode. If the circuit is not closed, unscrew the sensor and replace it with a new one.
8. Unscrew the oil filler cap and pour new oil into the engine through a funnel.
9. Check the lubricant level with a dipstick. It should be near the “max” mark.

That's it. After this, all that remains is to start the engine and check the joints for leaks.

In addition, it should be noted that original filter oil Daewoo does not have an anti-drainage valve. This fact must be taken into account when purchasing a new part.

Daewoo Nexia is a car that has good basic equipment. The machine is equipped with various volumes power plants, which are designed for a long working period. The Daewoo Nexia can be equipped with a manual (5 speed) or automatic (4 speed) gearbox. In this case, the engine can have 8 or 16 valves. Motor transport is unpretentious in operation.

The popularity of the machine is also explained by the fact that it has a low price and has good reliability.

Transmission SAE oil 80W class GL-4

On this vehicle, it is necessary to change the oil in the manual transmission at 100,000 km. As a rule, by this time the owner of a foreign car may encounter such manifestations as difficulty changing speeds.

The oil level should be checked every 15,000 km. As a rule, scheduled maintenance is scheduled for this time period. When operating a foreign car in aggressive conditions, the need to replace fuel may arise even up to 100,000 km. Fuel must be filled with exactly the same characteristics as the liquid added earlier.

What kind of oil is poured into car system? It should be noted that for the Daewoo Nexia model, oil with the following characteristics is suitable: SAE 80W class GL-4 (mineral).

Semi-synthetic oil can be added to the gearbox. 75W80 gear oil has high protective properties. It has an optimal viscosity index, extends the operating life of the speed box. New fluid should be added until it begins to flow out of the control hole. Using a filling syringe, new fuel is added to the gearbox. How to change gearbox oil?

Changing the gearbox oil

To change the oil in the Daewoo Nexia checkpoint, vehicles should be driven onto an overpass. Before this you need to drive a few km. For filling tools, you should use a special filling syringe, wrench, container, and socket heads. In most cases, when a replacement is carried out, it will be necessary to install a new pan gasket.

1. A number of car versions have protection on the crankcase. She's filming.
2. Since the manufacturer does not provide a drain hole for this version of the car, it is advisable to twist the gearbox pan. It is removed using a socket head.
3. It helps to completely drain the fuel if you jack up the front left wheel. In time, the oil will drain for about 20 minutes. The driver must pay attention to the condition of the spilled liquid.
4. The plug is located under the inner CV joint.
5. The removed plug and magnet should be cleaned of settled dirt. The tray also needs to be cleaned. You must carefully remove the pan so as not to spill oil on yourself.
6. The gasket is replaced with a new consumable.
7. The removed pan is installed in place.
8. The breather is removed using a mechanic's wrench. By opening the breather, new oil is poured into the transmission system.
9. Use a syringe to fill the hole with a new one. transmission fluid. An alternative to a syringe can be a funnel that is connected to a hose.
10. The breather is screwed in.

Finally, you need to turn on the engine and drive the car through each gear several times. As a rule, the oil level in the gearbox drops slightly, after which fuel should be added to the system.

Important! It is better to change the oil in the Daewoo Nexia gearbox on a warm gearbox. This is necessary so that the oil is more liquid, which contributes to its better permeability. What is the oil volume? In terms of volume, you have to pour approximately 1.7-1.8 liters of new oil into the system. However, the oil does not completely pour out of the gearbox. There are a few ml left in the gearbox.

Thus, the replacement procedure requires endurance. Timely maintenance will allow the vehicle owner to avoid expensive repairs to the vehicle system.

Owners of a Daewoo Nexia car often face the problem of replacement transmission oil. For those new to driving, it is difficult to determine which product to use and how much. For new Daewoo cars, the replacement procedure is not worth performing. This is due to the fact that the manufacturer has provided for the use of lubricating fluid for 7-10 years of regular operation of the machine or for 100-150 thousand kilometers. The instructions for the vehicle are silent on these terms, so you should listen to the specialists and promptly change the transmission oil in the gearbox.

Preparing for replacement

First of all, the motorist will need to purchase lubricating fluid and a gearbox cover gasket. If the part cannot be found for certain reasons, it is worth acquiring a special silicone sealant. Many people are interested in the question: how much should be poured, and which product to choose? To replace, you should purchase 2 liters of lubricant.

For the car model in question, the manufacturer recommends using oil marked SAE 80W GL-4 if vehicle operated in optimal conditions. For regular use at low temperatures, it is worth filling with 75W-90 GL-4.

Choosing a car oil suitable for replacement is quite simple. The manufacturer allows the use of both synthetic and mineral substances in the gearbox. The first option is more preferable in terms of quality, but has high cost. It is recommended to use a synthetic or semi-synthetic substance designated 75W80, 80W85, 75W-90 and GL-4.
When deciding which one is worth buying and how much you need, you should also trust experienced drivers. Based on their reviews, we can say that the optimal purchase would be synthetic products that have a volume of 2 liters.

Replacement procedure

Having determined how much lubricant to pour into the gearbox, you can begin the procedure. Replacement is carried out in stages:

This completes the transmission oil change.

Motorists cannot check what substance the gearbox consumes if it is filled at the factory. For the machine model in question, a mineral product is mainly used. It is advisable to replace it, especially when operating the car at low temperatures. This is due to the fact that it thickens greatly in such conditions. This will negatively affect the operation of the transmission.

The lubrication level should be checked every 15,000 km to ensure that it is not running low. This procedure can be performed by specialists during the maintenance. If necessary, add new fluid. Replacement will be required when the transmission is repaired. It is also worth pouring new fluid if the mechanism requires the use of a composition with a different viscosity.

By learning what lubricant can be used for your transmission and how to change it, the replacement will be completed properly. Motorists should pay maximum attention to this procedure, as the comfort and safety of driving depends on it.

Car enthusiast tips: choosing transmission fluids

And a little about the author’s secrets

My life is not only connected with cars, but with repairs and maintenance. But I also have hobbies like all men. My hobby is fishing.

I started a personal blog in which I share my experience. I try a lot of things, different methods and methods to increase my catch. If interested, you can read it. Nothing extra, just my personal experience.

Attention, TODAY only!