Where is the accent oil filter located? Changing the oil in a Hyundai Accent engine: which is better and how much to pour. Tools and materials

It is better to perform the operation on a warm engine immediately after a trip, until the oil has cooled down.

We install the car on an inspection ditch or overpass.

Unscrew the oil cap filler neck.
Below the car...

We start the engine for a few minutes. We make sure that the warning light for emergency oil pressure in the engine has gone out and there are no leaks from under the plug and filter.
Delayed shutdown allowed warning lamp after starting the engine for a few seconds, since it takes time to fill the channels and filter of the engine lubrication system with oil.
We stop the engine and after a few minutes (so that the oil flows into the crankcase pan) check the oil level (see “Checking the oil level in the engine crankcase pan”) and bring it to normal. If necessary, tighten the oil filter and drain plug.

If the car owner gets into the Hyundai Accent in a timely manner, this will significantly extend the life of the engine, protect against serious breakdowns and prevent high costs for repairs. It is important not only to carry out this procedure on time, but also to select the oil itself in accordance with the operating characteristics of the car and the requirements of the Korean automaker. You can do this kind of work yourself if the car is no longer under warranty. That’s why most car owners prefer not to seek help from a service station.

Engine oil in the engine Hyundai Accent should be replaced regularly.

Replacement frequency

First, the driver must understand how often the Hyundai Accent is driven. If you rely only on the official factory manual, then there you will see figures of 10 - 15 thousand kilometers. But these are conditional indicators, since the real interval between oil changes is actually much shorter. This is due to the fact that the manual specifies parameters aimed at almost ideal operating conditions, mild climate and high-quality roads. In Russia, the replacement interval becomes shorter, since the condition of the lubricant and its physical and chemical properties are influenced by the following factors:

• strong and sudden temperature changes between seasons;
• aggressive driving style;
• excessive regular load on the engine;
• use of towbar and trailer;
• long periods of idle time in traffic jams;
• poor quality of roads;
• use of low-quality fuel;
• speeding, etc.

Therefore, the actual interval between engine lubricant changes for the Hyundai Accent is about 6 - 7 thousand kilometers, or once a year. The car owner himself must monitor the condition and level of the oil, add it as necessary or change it completely. Some breakdowns or malfunctions can render the new oil unusable even after 500–1000 kilometers. Therefore, the driver is obliged to regularly monitor the serviceability of all components of the Accent. Experienced owners of Hyundai Accent cars advise, whenever possible and with very active use of the car, to change the lubricant in the engine every 6 months. This will allow the engine to work better and longer without serious problems and loss of engine life.

Oil selection

In the operating manual for the Korean brand Hyundai Accent, the manufacturer recommends that they meet official requirements. The main focus of the Accent is on the viscosity of the engine oil. It is optimal that the replacement is carried out using oils that correspond to the following values:

• 5W20;
• 5W30;
• 5W40.

The manual indicates this order, so first look for 5W20, and if you cannot find such a composition, follow the list. The performance of the engine largely depends on what type of oil you choose.

Owners of cars modeled around 2005 and 2007 complain that it is difficult to find branded lubricant with a viscosity of 5W20. Therefore, you have to select something from alternative offers on the market. Although the practice of Russian car owners clearly demonstrates that oil with the 5W30 index is excellent for a Hyundai Accent car in our climate. With it, the car behaves confidently and does not suffer from temperature changes.

The manual contains a list of several well-known manufacturers of motor oils that the Korean company recommends for its Accent. These are the following brands:

• Aral;
• Mannol;
• Liqui Moly.

These lubricants are recommended for more recent vehicles equipped with new power units. Such compositions increase oxidation resistance, have a long service life and help save fuel. Although the Accent cannot be called a car with high consumption, this is another small pleasant bonus. There are several oils that are not listed in the manual, but fully meet all the requirements for Hyundai Accent engines:

• Crypto 3 by Midland;
• Magnatec C3 from Castrol;
• Super Tronic Long Life III from Aral;
• Helix Ultra Extra famous brand Shell;
• Elf's Solaris LSX.

By pouring such oil into the engine, you will not violate the technological standards provided by the Korean automaker. In general, the Hyundai company should be given its due, since it does not tie its engines to a strictly limited line of motor oils, but allows car owners to choose from a wide list of lubricants on the market.

Replacement instructions

Before getting into the Hyundai Accent, you will need to collect a minimum set of tools and materials. The list is small, which makes it possible for car owners, even with a limited number of tools, to independently service the car and replace consumables on it. To the list necessary materials and tools include:

• • fresh oil in accordance with the required characteristics;
  • an empty container where you will drain the used lubricant;

• new filter (or filter element);
• new drain plug;
• a pair of keys (sizes 17 and 19);
• filter puller;
• the pit where the work will be carried out;
• a carrying lamp if there is not enough natural light;
• rags;
• personal protective equipment (thick clothing, gloves, closed shoes).

When you have prepared all the necessary tools and placed them near the car, you can begin to work. The entire procedure can be roughly divided into several stages:

• removal of old motor fluid;
• filter replacement;
• filling in new oil.

Let's go through them.

Draining old oil

Follow the instructions to avoid common mistakes or take the wrong path.

This completes the first stage. The mistake of many is that they simply forget or simply do not know about the need to simultaneously replace the oil filter.

Filter

You will still need the container where you drained the waste, so do not remove it too far. In the case of a filter, it is important to know in advance what type of device is installed on your Hyundai Accent car. Such machines are equipped with non-separable elements or those where only the filter element itself must be replaced. First of all, place the waste container under the filter. It is located on the left, near the top edge of the engine. The container is needed to allow the oil to flow out. Proceed further depending on the type of filter used.

If you have a non-separable design, then:

1. Take a puller or a suitable size wrench to unscrew the filter. It is dismantled in a counterclockwise direction.
2. Clean the slot where the filter is inserted thoroughly with a rag.
3. Compare your two filters. The old and new must be identical, otherwise some problems may arise.
4. The new filter has a sealing gasket, which must be lubricated with fresh engine fluid.
5. Reinstall the element. Tightening by hand is usually sufficient. But the body can slip in the hands, which is why some people use the tool. The tightening should not be too strong, but even if the tension is weak, leaks will occur through the seal.

That’s it, we’ve sorted out the non-separable type of filter device. Now about the features of the replaceable element in the filter housing. They work with it like this:

• dismantle the housing itself, drain the remaining engine oil into a container;
• clean the filter seat as in the previous case;
• Now on the body, find the cover mounting bolt, you need to unscrew it and remove it;
• Inside you will find a removable, replaceable filtration element;
• make sure that the new and old components are completely identical;
• insert it into place, replace the rubber seal, screw the bolt into place and lubricate the gasket with oil;
• the housing together with the new filter element can be put in place.

Everything is clear here. Nothing complicated. The main thing is that you do not accidentally damage the housing itself or lose the mounting bolt. Even if it accidentally fell into a container with motor oil, do not rush to get it out manually. The liquid is still hot, and you don't want any extra burns. Let's move on to pouring fresh engine lubricant.

Fresh oil

Next, we need to pour the required amount of fresh oil into the crankcase. And here the logical question arises about how much engine oil is needed for a Hyundai Accent. According to the official manual, Hyundai Accent engines contain 3 - 3.3 liters. It depends on the motor itself and its characteristics. But in practice, when self-replacement lubricating fluid there is a little less in the engine. The entire volume simply does not fit, since it is impossible to completely remove all the old liquid from the system.

Given this volume of oil in the Hyundai Accent engine, for the procedure you will only need to take a 4-liter canister. Use the remaining lubricant in the process of topping up as needed, plus this will simplify your task when looking for new oil for the next change of consumables. There is a canister, all the specifications are indicated, so finding an analogue will not be difficult.

Fresh motor fluid filled like this:

1. In the engine compartment, you have already unscrewed the filler plug. Fresh oil will be filled through it.
2. First pour out about 2.5 liters, let the oil drain into the crankcase. To do this, wait 5 - 10 minutes.
3. Use a dipstick to check the lubricant level. If it is not enough, add a little more.
4. If the dipstick shows normal, close the lid and start the engine. While it is idling, check the drain plug and filter for leaks. If a leak is detected, be sure to tighten all fasteners.
5. When the engine has warmed up, turn it off and take a test measurement. If the oil level meets the requirements, then all that remains is to return the plug to its place, install the pan protection and enjoy the achieved result.

It is recommended to take another level measurement after 2–3 days, plus additionally examine the condition of the floor under the car. The presence of even a small amount of fresh oil under the pan indicates that the seal is broken and the filter or drain plug needs to be tightened. At this point, the work on independently changing the engine oil in the Hyundai Accent engine can be considered completed, for which we congratulate you.

Thank you for your attention! See you again!

Any car needs maintenance. The Hyundai Accent is no exception. It is necessary to change the engine oil in the engine, according to the regulations, every 12-15 thousand km. Of course, you can contact a car service center, but you can carry out a shift with your own hands in half an hour.

Video

The video will tell you how to properly change the oil on a car, and also tell you about some of the nuances of the procedure.

Replacement process

Replacement Hyundai oils Accent is quite easy to do with your own hands. For the process to be successful, it is necessary to have minimal tools, as well as access to the vehicle from below.

When everything you need has been collected, you can proceed directly to the process itself:

1. First, you need to let the car cool down.
2. Open the hood.
3. To find a filter, you need to know design features. Access to the filter is closed with a lid, as is access to the drain neck.
   
4. We remove the protective covers and find access to the oil filter.
   
5. Open the access cover to the drain neck.
   
6. Unscrew it and engine oil will flow out.
   
7. When the oil is drained, tighten the drain plug. To avoid leaks, it is necessary to replace the O-ring.

   Oil filter seat. Removing the filter will also spill some oil. Lubricate the O-ring of the new oil filter with oil.
   

8. Before adding oil, we replace the oil filter element.

   Screw the new oil filter into place. When the oil stops dripping, wipe the drain hole and tighten the bolt.
   

9. Let's move on to the engine compartment. To fill engine oil, you need to unscrew the filler plug.

   Pour new oil into the engine. Screw on the cap and run the engine for a few minutes. Then check the oil level on the dipstick (add if necessary) and make sure there are no leaks on the drain hole and oil filter.
   

After filling the engine oil, after 5-10 km, you need to check the level. If necessary, add liquid.

Oil selection

Original number 0510000410 (4 liters, semi-synthetic, not for new cars), average price 1515 rubles. or 05100-00441 (4 l., synthetic, mainly for new cars), average price 2076 rubles. For replacement, engine oil with a viscosity of 5W20, 5W30, 5W40 is used.

Options for replacement:

• Aral 15503C — 2823 rub.
• Shell 550046364 — 1779 rub.

Selecting oil and filter

The choice of filter should be taken quite seriously, since this will determine how well the engine oil will be filtered. For Hyundai Accent engines, the catalog number will look like 26300-35503. Average price is 500 rubles.

Consider a list of analogues that can be used instead of a standard product:

Conclusion

Changing the filter and oil on a Hyundai Accent is quite easy on your own. To do this, you need minimal tools, as well as minor constructive skills. As for choosing a filter, you should take it seriously, since this will determine how long it will last.

Changing the oil in the Hyundai Accent TagAZ engine and other cars of this type model range is produced taking into account the manufacturer's recommendations for maintenance. The general procedure is standard and not complicated; the main attention is paid to the selection of components and the replacement sequence.

When is an oil change required?

The regulations for changing the oil in the Hyundai Accent engine provide periodicity 15 thousand kilometers. This figure is considered an average value; for Russian operating conditions it is reduced to 10 thousand km.

The frequency of engine oil changes is largely determined by individual factors car use:

• aggressive driving, driving at high speeds;
• city ​​traffic, frequency of stops;
• quality and surface of roads, dustiness;
• increased engine load, towing vehicles;
• conditions environment, significant differences in daily and annual temperatures.

Taking these factors into account, many car owners pay attention to signs that replacement is needed. These include the level and condition of the oil; for timely detection of problems, the relevance of preventive checks is emphasized.

The lubricant level is regularly measured with a dipstick. In a heated and normal state, the volume of lubricant should not exceed the permissible limits indicated on the measuring device.

Regarding the condition of the lubricating fluid, pay attention to external signs expired service life. These include a change in color, the appearance of sediment or impurities, and a burnt smell. It is not recommended to wait for more serious signs related to engine performance.

Checking the oil regularly allows you to replace the lubricant and filter on time, avoiding costly repairs. This step also ensures reliable operation of the engine and increases the resistance of its components to premature wear. At the same time, during prevention, the car owner can identify the required frequency of replacement at the individual level, taking into account the operating conditions of his car.

What kind of oil should I use?

The choice of oil for replacement in a Hyundai Accent engine is made in accordance with the manufacturer's recommendations. Regardless of the manufacturer, it is recommended to use synthetics. The technical properties of such a lubricant not only cope better with loads, but are also more resistant to thermal and oxidative reactions.

In question chemical composition the oil emphasizes its viscosity. When there are significant changes in annual temperature, universal options are purchased - 5W-30 and 5W-40. When choosing a manufacturer, the following are recommended: brands: Shell Helix Ultra, Liqui Moly, Lukoil Genesis.

When it comes to the amount of oil purchased, they usually focus on engine size. However, for Hyundai Accent cars the difference is insignificant, so they usually buy up to 3.5-4 liters of new lubricant.

Stages of changing the oil in a Hyundai Accent engine

To change the oil in a Hyundai Accent engine, a certain procedure is followed. Conventionally, it is divided into two procedures - preparation and replacement. The first includes the following actions:

• purchase of necessary consumables, new lubricant and filter;
• choosing a workplace;
• warming up the engine and preparing tools.

To purchase the necessary components, a preliminary inspection of the system is carried out. A simple preventive replacement requires only new lubricant, filter and drain plug gasket. However, if there are faulty connections, buy replacements for them too.

To work with purchased parts, choose a flat, comfortable platform. The optimal solution is to use a repair pit, overpass or lift. Supports with a jack are also suitable.

The oil is heated before draining the lubricant. It provides better circulation, but increases the risk of thermal burns from lubricant and engine parts. It is recommended to use gloves and overalls for work.

Taking into account the requirements in the list necessary tools include the following equipment:

• clothes that you don’t mind getting dirty, rubber gloves;
• clean, lint-free rags or rags;
• collar with attachments, set of socket wrenches, feeler gauge;
• container for draining oil with a volume of 4 liters;
• new lubricant, filter, gaskets and other components to replace worn and faulty parts.

Separately, the use of a special tool for removing the filter is highlighted. The casing can usually be unscrewed and tightened by hand without any problems. However, if difficulties arise, use various devices that are at hand.

Oil change in the Hyundai Accent engine, do it yourself according to the following step-by-step instructions:

• after warming up, uncork the filler neck;
• in the lower part, remove the engine protection, if any;
• Place a container under the drain to collect used lubricant and uncork the plug;

• While the lubricating fluid is draining, check the plug and change its gasket;
• Place a container under the filter; when removing it, residues may spill;

• unscrew the casing, check and replace the filter, lubricate the rubber seals with oil before tightening;

• the filter is mounted in place; when screwing, make sure that the seals do not come out of the grooves;
• after draining the used oil, clean the plug and drain hole and seal it;
• New oil is poured into the system, the engine is warmed up for several minutes;
• check the lubricant level, as well as the tightness of connections for leaks.

There is a separate procedure for cleaning the engine from lubricant residues. This is done when changing the type of oil, for example, if synthetic is poured instead of semi-synthetic.

Wash the engine using a special product before changing the filter. The cleaning procedure is simple: after draining the waste, plug the plug, fill in the wash, and warm up the engine. Next, drain the flushing agent, change the filter and fill in a new lubricant.